How to Add a Drip Zone to an Existing Sprinkler System: A Step-by-Step Retrofit Guide
As gardens mature, landscaping needs inevitably shift. You might decide to convert a section of your open lawn into a decorative flower bed, establish a new hedge line, or plant a dedicated vegetable plot. When this happens, traditional high-pressure pop-up sprinklers are no longer the most efficient option. Instead, you need the targeted precision of micro-irrigation. Learning how to add a drip zone in an existing sprinkler system allows you to maximize water conservation while keeping your new plants perfectly hydrated without overhauling your entire pipe network.
However, retrofitting micro-irrigation into a network designed for high-pressure spray heads requires careful planning. Below, our technical team breaks down the professional, step-by-step engineering process to convert or split your current setup safely and efficiently.
The Golden Rule: Never Mix Sprinklers and Drip Lines on the Same Zone
Before sourcing fittings, it is vital to understand a core principle of hydraulic design: you must never run pop-up sprinklers and drip lines simultaneously on the exact same zone valve. Doing so will cause localized system failure due to two critical imbalances:
- Pressure Disparity: Pop-up sprinklers generally require high operating pressures between 2.5 to 4.5 Bar to perform. Drip lines, porous pipes, and micro-emitters are low-pressure components engineered to run optimally between 1.0 and 2.0 Bar. High pressure will burst drip fittings or blow emitters straight out of the pipe wall.
- Precipitation Rates: Sprinklers dump large volumes of water quickly (measured in litres per minute), while drip lines distribute water incredibly slowly (measured in litres per hour). Running them on the same timer cycle will either completely flood your lawn or leave your flower beds bone-dry.
Method 1: Converting an Entire Existing Zone to Drip
If you have completely removed a section of turf to make way for shrubs or flower beds, completing an add a drip zone in an existing sprinkler system project by converting that specific zone entirely to micro-irrigation is the cleanest approach.
Step 1: Cap Off Unused Sprinkler Heads
Locate all the pop-up bodies within that zone. Remove the internal sprinkler assemblies and cap off the underground threaded fittings using high-quality PVC blanking plugs or male threaded caps. Leave one strategic sprinkler head active—ideally the one closest to the start of the zone pipeline layout—to serve as your new drip connection point.
Step 2: Install a Retrofit Drip Control Zone Kit
At your chosen remaining sprinkler connection, install a specialized retrofit kit (such as a Rain Bird or Hunter micro-control zone assembly). This component screws directly onto the existing riser pipe or pop-up body and houses two non-negotiable tools:
- A 1.5 or 2.0 Bar Pressure Regulator: Steps down the high mains supply pressure to a safe, continuous pressure for the drip network.
- A High-Mesh Irrigation Filter (120-200 mesh): Essential for catching fine sand and debris that would otherwise instantly clog the tiny emitter paths inside your drip line.
Step 3: Lay Out Your Drip Line Network
Connect your primary 16mm or 20mm MDPE blank supply pipe to the regulator outlet using secure compression or nut-lock fittings. Roll out your pressure-compensating drip line across the root zones of your plants, securing the pipe network to the soil with heavy-duty metal ground stakes, and seal the ends using end-plugs or figure-eight flush valves.
Method 2: Teeing into a Mainline to Create a Brand New Zone
If your current automated zones must remain untouched, you will need to cut into your primary underground mainline pipe network to install a completely independent, dedicated micro-irrigation zone valve assembly.
Step 1: Expose and Cut the Mainline
Isolate your main water supply. Excavate a clean trench around your primary mainline upstream of your existing valve manifold box. Clean the pipe thoroughly and use an industrial pipe cutter to make a straight cut into the MDPE line.
Step 2: Insert a Compression Tee and New Solenoid Valve
Install a premium PN16 compression tee fitting (such as a Supreme S16 fitting) to branch off the pipe line. Run a new section of pipe into a secure underground valve box. Inside this box, install a new 24V or battery-operated electric solenoid control valve (e.g., Rain Bird 100-DV) to govern the zone via your irrigation controller.
Step 3: Build the Low-Pressure Assembly
Immediately downstream of your new solenoid valve, you must screw in your dedicated pressure regulator and mesh filter. From there, you can transition safely out of the valve box using a standard barbed adapter to link directly into your low-pressure surface drip infrastructure.
Essential Equipment Checklist for Your Retrofit Project
To successfully modify your system layout, ensure you have the correct commercial-grade hardware ready before commencing installation:
- Pressure-Compensating Drip Line (PC Drip): Ensures every plant receives an exact, uniform volume of water regardless of whether it is at the start or the very end of the pipe line run.
- Pressure Regulator & Inline Filter: The ultimate defense system against physical line blowouts and internal emitter blockages.
- Nut-Lock or High-Quality Barbed Fittings: Essential for making reliable connections on flexible poly pipes without the risk of leaks under pressure variations.
- Blanking Plugs & Riser Caps: For cleanly sealing up redundant pop-up sprinkler bodies beneath the soil level.
Need Professional Engineering Support?
Modifying automated pipe networks can occasionally feel overwhelming without a clear blueprint. At MB Irrigation, we specialize in helping UK landscapers, groundsmen, and DIY property owners optimize their watering infrastructure. If you are unsure how many zones your water flow rate can support or need help picking the right compression fittings, send our technical team in Warrington a basic sketch of your garden setup. We will map out a precise, custom product specification list for your project.